Prawidłowo używaj podczerwień termometr diagnozuj sprzęt usterki
The core problem of infrared diagnosis of equipment faults recommended by infrared thermometers is to accurately obtain the temperature distribution of the equipment under test or the temperature values and temperature rise values of fault-related points. This temperature information is not only the basis for judging whether the equipment is faulty, but also the objective basis for judging the fault attribute, location, and severity. Therefore, the calculation and reasonable correction of the temperature of the fault-related parts of the equipment under test is a key link to improve the accuracy of the surface temperature of the detection equipment. However, when infrared detection of equipment is performed on site, due to changes in detection conditions and environmental influences, the same equipment may obtain different results due to different detection conditions. Therefore, in order to improve the accuracy of infrared detection, corresponding countermeasures and measures must be taken during the on-site detection process or during the analysis and processing of the detection results, or good detection conditions must be selected, or reasonable corrections must be made to the on-site detection results.
Wśród nich, wpływ stanu stanu wyposażenia elektrycznego:
Electrical equipment faults are generally heating faults caused by current effects (conductive circuit faults - heating power is proportional to the square of the load current value), and heating faults caused by voltage effects (insulation medium faults - heating power is proportional to the square of the operating voltage). Proportional). Therefore, the operating voltage and load current of the equipment will directly affect the results of infrared detection and fault diagnosis. The increase in leakage current can cause uneven voltage in parts of high-voltage equipment. If there is no load operation or the load is very low, the heating of the equipment failure will not be obvious. Even if there is a serious failure, it will not be exposed in the form of characteristic thermal anomalies. Only when the equipment is operating at rated voltage and the load is greater, the heat generation and temperature rise will become more serious, and the characteristic thermal anomalies at the fault point will become more obvious.
W ten sposób, kiedy wykonuje podczerwień wykrywanie, w kolejności uzyskanie niezawodne wykrywanie wyniki, powinniśmy spróbować nasz najlepszy do upewnienia się a na sprzęt działa natężenie napięcie i pełne obciążenie. Nawet jeśli nie może osiągnąć ciągłego pełnego obciążenia działania, an działania plan powinien być przygotowany do ułatwienia the wykrywania podczas the detekcji. Podczas przedoperacyjnej i testowania procesu, ten sprzęt może być uruchomiony na przy pełny obciążeniu przez a okres czasu, tak tak ten wadliwy część sprzętu ma wystarczająco czas do czasu na nagrzanie w górę i upewnienie się to powierzchnia osiąga stabilna temperatura wzrost. Podczas podczerwień diagnoza elektryczności sprzętu usterki, usterki usterki osąd standard jest często oparte na na na temperaturze wzrost urządzenia przy prądu znamionowym prądzie. W związku z tym, kiedy rzeczywisty działa prąd podczas wykrywania jest mniejszy niższy znamionowy prąd, temperatura wzrost urządzenia usterka punkt faktycznie zmierzony na miejscu powinien być przekształcony na prąd znamionowy prąd. Temperatura wzrost z prądu.
Sprzęt powierzchnia podczerwień pomiar instrumenty uzyskać sprzęt temperatura informacje poprzez pomiar podczerwień promieniowanie zasilanie na powierzchnia urządzenia elektryczne na. I kiedy podczerwień podczerwień diagnostyczny przyrząd odbiera ten sam podczerwień promieniowanie moc z celu, inny detekcja wyniki będzie uzyskany ze względu na inny powierzchnia emisyjność z celu. W inne*słowa, dla to samo promieniowanie moc, niższe emisyjność%% 2c , wyższa temperatura będzie wyświetlana. Ponieważ powierzchnia emisyjność obiektu jest głównie określona przez materiał właściwości i powierzchnia stan (taki jako powierzchnia utlenianie, powłoka materiał, chropowatość i zanieczyszczenie stan, itd.).
Efekty Atmosferyczne Tłumienie:
podczerwień promieniowanie energia na na powierzchni urządzeniach elektrycznych pod test jest przepuszczany do podczerwień detekcji przyrządu przez atmosferę, co będzie pod wpływem absorpcja tłumienie cząsteczek gaz cząsteczek takich jako woda para, węgiel dwutlenek, i węgiel tlenek węgla w w atmosferze kombinacja i rozpraszanie tłumienie zawieszone cząstki w powietrzu w powietrzu.
