Często usterki z elektryczne żelazo_The konserwacja metoda z elektryczne żelazo
1. Elektryczny żelazo nie ciepło po bycie pod napięciem
If the soldering iron does not heat up after being powered on, it means that the soldering iron has an open circuit fault. This fault may occur at the plug of the soldering iron in sever places. The soldering iron iron erdzeń is broken, the lead wire the solder iron core is broken, and the power cord of the soldering iron is broken.
2. The tip of the soldering iron does not eat tin
Do not eat soldering iron tip "Tin Pu sees that the newly purchased soldering iron tip is used direct without trimming, resulting in no tinning of the solder iron tip. The solder iron tip that has been used for a long time is not tinned, and the solder iron tip is burnt to death and needs to be repaired.
3. The electric soldering iron is charged
Elektryczny żelazo jest bardzo niebezpieczne dla spawania personel% 2c i poważne elektryczne wstrząsy wypadki wystąpią. Dlatego , raz elektryczny żelazo jest znaleziono do być zelektryfikowany% 2c moc zasilanie dostawa powinien być odciąć natychmiast do inspekcji. Istnieje kilka kilka powody dlaczego elektryczne żelazo jest zelektryfikowane. Zasilanie przewód z elektryczny żelazo jest podłączone do zacisk z uziemienie przewód; zasilanie przewód upadki off z zacisk żelazo rdzeń i wtedy dotyka śruba z uziemienie drut, przyczynowe the power lead wire of the solder żelazo głowica to be plątane and przyczyna wyciek; moc uziemienie sama przecieki elektryczność.
4. Tam są studzienki na końcówka żelazko
Kiedy elektryczny żelazo jest używany dla a okres z czas, wgłębienia lub utleniony korozja warstwy pojawią się na żelazo końcówka, która zmiany kształt z ostrze powierzchni z żelazo końcówka. w to przypadek, tlenek warstwa i doły can be filed off with a file, and filed into the original shape, and then tinned, and then it can be reused.
Naprawa metoda z elektryczny żelazko
1. The maintenance method that the solder iron does not heat up after being powered on
(1) Kiedy żelazo jest naenergetyzowane, it is found that the soldering iron head is not hot. Ogólnie, the power cord has fallen off or the core wire of the solder iron is broken. If it does not move, it means that there is an open circuit fault.
(2) Pierwsze sprawdzenie czy the lead wire of the plug itself is open circuit phenomenon, if not, you can remove the bakelite handle, and then use a multimeter to measure the the two lead wires of the solder iron core, if the pointer of the multimeter still does not move, it means that the solder iron core is damaged, and the soldering iron should replaced Heart.
(3) The resistance between the two leads of the 35W internal heating soldering iron core is 1. Around Skfl, if the measured resistance value is normal, it means that the solder iron core is good, and the fault occurs in the power lead and the plug itself, and most of the faults are lead wire open circuit. To jest konieczne do wymiany żelazo rdzeń % 2c wstaw a nowe żelazo rdzeń z tego samego specyfikacji w połączenie połączenie pręt 2c fix przewód przewód na mocowanie śruba 2c i dokręcenie zacisk zwarcie obwód.
2. Konserwacja metoda z żywa żelazo głowica
(1) The reason for the electrified fault of the solder iron tip is that, in add to the wrong connection of the power line to the grounding line terminal, there is another reason, that is, when the power line falls off from the terminal of the solder iron core, it touches the the screw of the grounding line again. As a result, the tip of the solder iron is – opłata.
(2) To rodzaj awaria może łatwo przyczyna elektryczny wstrząs wypadki i uszkodzenia komponenty. W zamówieniu do zapobieżenia zasilanie przewód od upadek off, it is necessary to regularnie sprawdzaj czy zaciskanie na uchwyt z elektryczny żelazo są luźne lub brakujące. Przygotowane w czas.
